SEC-16 • Tools, Equipment & Machinery • 29 CFR 1926.300–307 (Subpart I) & 29 CFR 1910.241–244 (Subpart P)

Hand & Portable Power Tools, Guards & Pneumatic/Powder-Actuated Tools

Machine guarding of blades and abrasive wheels, angle grinder RPM ratings (wheel RPM ≥ tool RPM), pneumatic hose whip-checks and safety clips, powder-actuated tool licensing, and prohibition of trigger-locks on hand-held saws/grinders.

Buy Single Written Program ($49) → Buy All 24 Programs — Complete Manual ($149) Open in Full Interactive Customizer

Mandatory OSHA & RAVS® Audit Elements Covered

Every Hand & Portable Power Tools, Guards & Pneumatic/Powder-Actuated Tools document generated by Trade Safety Manuals is pre-merged with your Company Name and Designated Safety Director and addresses these required regulatory provisions:

  • Keep all manufacturer guards in place and operable on circular saws, angle grinders, chop saws, and portable tools; tampering with or wedging guards open is a zero-tolerance violation
  • Verify on every abrasive grinding/cut-off wheel that the maximum RPM rating stamped on the wheel equals or exceeds the no-load RPM stamped on the grinder spindle, and perform a ring test before mounting
  • Secure all pneumatic air hose connections (>1/2 inch ID) with positive locking pins and steel whip-check cables; never use compressed air >30 psi for cleaning
  • Operate powder-actuated tools (Hilti/Ramset) only if trained and carrying a valid operator card; never leave a loaded powder-actuated tool unattended
OSHA Construction Standard: 29 CFR 1926.300–307 (Subpart I)
OSHA General Industry Standard: 29 CFR 1910.241–244 (Subpart P)
RAVS® / Portal Category: Tools, Equipment & Machinery
Required Employee Training Interval: Initial orientation + tool-specific qualification (mandatory manufacturer card for powder-actuated tools)
Competent Person Inspection Frequency: Pre-use inspection of cords, plugs, guards, switches, and discs before each shift

Required PPE & Instant Custom Sample Download

Mandatory Personal Protective Equipment (PPE) & Controls Specified:

  • Safety Glasses + Full Face Shield (for grinding/cutting)
  • Hearing Protection
  • Anti-Vibration / Cut-Resistant Gloves (keep clear of rotating chucks)

Customize & Download Free Sample (.DOC)

Enter your company details below to download an editable Microsoft Word copy of SEC-16: Hand & Portable Power Tools, Guards & Pneumatic/Powder-Actuated Tools immediately:

Upgrade to Complete 24-Chapter Manual + State Plan ($149) →

Browse All 24 Written OSHA & RAVS® Safety Programs:

SEC-01: Injury & Illness Prevention Program (IIPP) / Corporate Safety PolicySEC-02: Fall Protection, Guardrails & Post-Fall Rescue PlanSEC-03: Control of Hazardous Energy — Lockout / Tagout (LOTO)SEC-04: Electrical Safety, Arc Flash & NFPA 70E Compliance ProgramSEC-05: Trenching, Excavation & Underground Utility ProtectionSEC-06: Permit-Required Confined Space Entry (Construction & General Industry)SEC-07: Respirable Crystalline Silica Written Exposure Control PlanSEC-08: Hazard Communication (HazCom) & GHS Safety Data Sheets ProgramSEC-09: Fire Prevention, Welding, Cutting & Hot Work Permit ProgramSEC-10: Portable Ladders, Stairways & Safe Access ProgramSEC-11: Supported & Mobile Scaffolding Safety ProgramSEC-12: Mobile Elevating Work Platforms (MEWPs) — Aerial & Scissor LiftsSEC-13: Cranes, Derricks, Rigging & Qualified Signal Person ProgramSEC-14: Personal Protective Equipment (PPE) & Hazard Assessment ProgramSEC-15: Heat Illness Prevention, Acclimatization & Hydration PlanSEC-16: Hand & Portable Power Tools, Guards & Pneumatic/Powder-Actuated ToolsSEC-17: Respiratory Protection, Medical Evaluation & Fit Testing ProgramSEC-18: Heavy Earthmoving & Mobile Equipment, Spotters & Traffic ControlSEC-19: Compressed Gas Cylinders, Refrigerants & Mechanical Piping SafetySEC-20: Bloodborne Pathogens, First Aid & Sewage/Biohazard Exposure ControlSEC-21: Emergency Action Plan (EAP), Medical Evacuation & Severe WeatherSEC-22: Incident Investigation, Root Cause Analysis & OSHA 300 RecordkeepingSEC-23: Subcontractor Safety Prequalification & Multi-Employer CoordinationSEC-24: Occupational Noise Exposure & Hearing Conservation Program